- Powerwise Qe Ez Go Charger Service Manual Pdf
- Ezgo Charger Powerwise Qe Reset
- Ez Go Charger Manual
- Ezgo Powerwise Qe Charger Manual
@ppbbeamer Paul, Links below are informative on golf cart chargers, 1st link is for your battery chargers manual, the other 2 links are testing/trouble shooting guides, Good luck. I hope this helped you out, if so let me know by pressing the helpful button. The NEW Lester Summit II Multi-Voltage 36V/48V Battery Charger can be INSTALLED ON-BOARD OR USED AS A STATIONARY CHARGER ON ANY 36 VOLT OR 48 VOLT EZGO GOLF CART (that takes the triangle shaped plug with 3-pins). If you’re driving the Batmobile, and it’s 36V OR 48V with an EZGO triangle receptacle, it may even charge that, too.
There doesn't seem to be a day that goes by at RMI Golf Carts that we don't receive phone calls or emails on the topic of battery chargers. Many times folks ask 'do you guys sell chargers'? The answer is of course 'yes'! But like we tell everyone that calls, more than likely you don't need to buy a new charger. Many people are shocked to know that most of the time they can be repaired.
Once this has been established, the next question is “How do I determine if it’s bad”, and 'I’m pretty handy, what parts do I need'!! Mocha tn5250 tutorial.
Exocad crack. So, we’ve decided to put together a 'How to' video on repairing the EZ-GO Powerwise Charger. This is the charger that works on all EZ-GO PDS 36 volt carts. It seems to be the most popular charger out, and it’s the one we see the most.
Items you will need to repair and troubleshoot your E-Z-Go Powerwise Charger
Tools Needed | Parts You May Need |
Philips head screw driver | Diode Stud Type - 2010 |
Needle nose pliers | E-Z-Go Powerwise Control Board |
7/16 wrench | Powerwise 50 Amp Fuse |
Voltage meter with buzzer |
E-Z-Go Powerwise Charger troubleshooting quick guide
Did you check the end of the Powerwise charger handle?
More often than not the issue is with the charger handle. Inside the charger handle there's a little clip. These clips wear and get pushed out of place. Epic browser for mac. Pull the clip back out, so that it is grounded to the post.
Did you check the charger cord?
Powerwise Qe Ez Go Charger Service Manual Pdf
People have a tendency to yank the cord out when they’re done charging, this can damage it. With power supply plugged in, lift up on the cord rotate it different directions to see if the charger comes on. Windows 95 98 se me ram limitation patch 2017. If the charger doesn’t come on, then you have a bad connection somewhere else.
Did you check the fuse on the Powerwise charger?
Unplug the charger. Use the voltmeter and ground it to the screw next to the fuse, and press the other end to the opposite side of the fuss. If it was a bad fuse you voltmeter wouldn’t buzz or beep. If you have a bad fuse, here is the part number for the E-Z-Go Powerwise charger: replacement 50 amp fuse part number is 2810601G01
Ezgo Charger Powerwise Qe Reset
Did you check the diodes on the charger?
Ground the heatsink board. With the other wand, touch each diode separately. If any of the diodes beep or buzz, then all of the diodes need to be replaced. The part number for the Powerwise replacement diodes is 18488G1.
Did you take a look at the motherboard of the Powerwise charger?
If the charger comes on by pressing a screwdriver to the black connector, you know it’s bad (see video for details). The replacement part number for the Powerwise charger motherboard is 28667G01.
Did you check for current continuity along the charger handle and cord?
Ez Go Charger Manual
Use your voltmeter to test the positive end of the charger handle. Press the other end to the negative line coming in (near the fuse). This is just one last check to be sure, since often the handle of the E-Z-Go Powerwise Charger is where people tend to have issues.